breakingthe lines

What Football Clubs Should Know Before Adding a Sauna to the Training Ground

4d ago4 min

Imagine it’s Thursday afternoon. The first team has finished training, six players want to use the sauna, and the academy squad is due in the changing room half an hour later. On the architect’s drawing, the sauna is a tidy rectangle beside the showers. On the training schedule, someone has to decide when to switch it on, how many players can use it comfortably, and who gets the next slot.

A recent enquiry at SaunaHeaters.com illustrates how quickly the equipment question can get ahead of the design. A commercial customer planning a 2,070-cubic-foot sauna wanted to know whether two heaters could run from one master control. It was a sensible question, and one a football club might ask when it wants staff to manage the whole room from a single point. But the answer depends on the specific heaters, the control system, and the manufacturer’s approved configuration.

Start with the busiest hour of the week

Before asking suppliers for prices, put a typical training week in front of the facilities manager and the kit staff. Pick the hour when demand will be highest and ask who will actually use the room together. A squad of 22 might use a sauna in small groups over an afternoon, while a club sharing facilities across several teams might need to turn the room over much faster. Those are different briefs, even if both clubs have the same number of players.

There’s a useful exercise to do before the plans are signed off. Mark the proposed benches and doorway on the floor, then ask a few people to sit where the drawing says they’ll sit. Can the player at the far end get out without everyone else standing up? It’s an inexpensive way to find out whether a room described as a six-seater will work that way on a busy afternoon.

Give the heater supplier more than a floor plan

Two rooms with the same floor area can have different heating requirements. Ceiling height determines the volume of air in the room, and exposed glass or masonry affects the calculation. Harvia’s sizing guidance treats each square metre of glass or a comparable uninsulated surface as equivalent to an additional 1.2 cubic metres of room volume. If your club is comparing Harvia sauna heaters, use that adjusted volume to narrow the shortlist, then check the recommended room size in each model’s manual.

“I’d ask the club for two things up front: a drawing that shows the ceiling height and glass, and the timetable for its busiest training day. The drawing helps us size the heater. The timetable tells us how the staff expect to use it.” says Ryan Williams, Sauna Expert at SaunaHeaters.com. 

For an estimate, a club can enter its dimensions and glass area into a sauna heater size calculator. Keep the measurements with the estimate so the facilities manager can see what changes if, for instance, the architect widens the glazed front. Once the room layout is settled, ask the supplier to check the result against the installation manual for the exact model being quoted. 

Ask what the staff will have to manage

The most useful part of the 2,070-cubic-foot enquiry was the question about one control. The customer was already thinking about the person who would have to operate the finished room. For a club comparing commercial sauna heaters, that’s a good test for each proposal: ask the supplier to name the heaters, controller, and any additional power units, then show where the manufacturer documents that combination. That gives the club and its electrical contractor something concrete to review before placing an order.

It’s also worth asking who’ll look after the room on an ordinary Tuesday. Who starts it before the first session, who shuts it down after the last one, and who does the kit manager call if the controller shows a fault? Ask where the model and serial numbers will be recorded and whether the person responsible for maintenance will have access to the manuals. These details are easy to settle while the supplier and installer are still involved.

Know what belongs in the quote

When the club is ready to request a project quote, send the interior dimensions, ceiling height, glass measurements, expected hours of use, and any drawings already available. Ask each supplier to distinguish what comes with the heater from what must be purchased separately, including controls, stones, and any required power units. Two prices are much easier to compare once you know whether both would buy a complete system. 

Before signing off, bring the conversation back to that Thursday afternoon. Ask the person who’ll run the room to walk through the first team’s session, the academy handover, and the end-of-day shutdown. If they can explain how each part will work, the club has answered a much better question than simply how large a heater it can fit.

Author

Tina Bahadur works in operations at SaunaHeaters.com, a specialist retailer serving homeowners, builders, and commercial facilities. Her work gives her a practical perspective on the questions buyers bring to a sauna project, from what to include in a quote to which details to confirm before placing an order.

BT
0subscribers